Stud Finder Wall Scanner Wood and Metal Detector Sensor for 3/4 inch Thickness Wall (Yellow)
14 sold in last 24 hours
- Light Indicator and Audio Alarm: ST100B stud finder is equipped with 4 level-flash-light, light up every time a stud edge is approached or be located, in the meanwhile, the beeping will let you know you stop move once you find the edge of wood or metal behind the wall
- Affordable and Accuracy: No more modes you need to learn, just keep it simple. Holding the button, it beeps right away for 2 seconds (it's calibrating), hold it over a non-stud area. When it's done, now you can slide it around to detect (keep holding button) until you find the edge of a stud
- Why You Need eOUTIL Stud Finder: eOUTIL stud detector quickly locates wood, metal and joist hidden in the walls, floors and ceilings of the house. It can work on different wall surfaces, such as lath, wallpaper wood flooring, acoustic ceiling, painted walls, etc. helping you avoid danger when installing TVs, cabinets, garage racks, etc. 3/4 Inches Deep Detection for Wood and Metal
- Electrical stud finder: eOUTIL stud finders actively detect differences in wall density to find studs. It uses with a 9v 6F22 battery (Not included) as a power source
- Specification: 5.5 x 2.9 x 1.2 inches; 3.6 oz weight
Tags |
Estimated shipping
Select a product to estimate shipping.What Is A Stud Finder?
As the name suggests a stud finder detects studs behind the surface of a wall.
Detection is achieved using two different methods:
1. Magnetic
Uses powerful magnets to pinpoint the location of screws or nails in a stud. Therefore it doesn't detect the stud itself but rather the hardware that attaches the wall material to the stud.
2. Electronic
Electronic stud finders rely on sensors that detect changes in the dielectric constant (the relative permittivity) of the wall. This changes when the sensor is over a stud. The lower reading indicates the presence of a stud in the wall and the signal will let you know by the colored lights. eOUTIL ST100 stud finder is an electronic style.
How To Use eOUTIL ST100 Stud Finder?
Step 1: Take off the battery cover and load your own 9V 6F22 battery, then ready to go
Step 2: Place the device flat on the wall. Then press and hold the button while keeping the unit still until calibration is complete (1 - 2 seconds). When calibration is complete, the unit will sound a short beep
Step 3: While holding on the button, move it along the desired surface to scan.
Step 4: When the stud finder detects a side of object, it will beep continually and flashing the lamp, mark this place with a pen, keep moving to find another side, mark again.
Stud-Finding Tips: Don’t touch the wall with either hand while you’re using a stud finder—this can alter its readings.
How to load your own 9V 6F22 battery?
Product details
| Main Specification | |
|---|---|
| Produttore | eOUTIL |
| Conteggio unità | 1 conteggio |
| Dimensioni L x W x H | 2.56"L x 1.57"W x 1.57"H |
| Tipo di esposizione | LED/Beeping |
| Marca | Eoutil |
| UPC | 786118036321 |
| Numero di articoli | 1 |
| Utilizzazioni consigliate per il prodotto | Rilevamento del metallo |
| Fonte di energia | Batteria alimentata |
| Materiale | Plastica |
| Colore | Giallo |
| Articolo Peso | 3.2. |
| Product information | |
| Tipo di batteria | 9V |
| Operating Frequency | 10 KHz |
| Technical Details | |
| Numero parte del produttore | ST100 |
| Batterie richieste? | Sì. |
| Tipo di materiale | Plastica |
| Valutazione della protezione internazionale | IP54 |
| Item details | |
| Numero del modello | STATO |
| Others | |
| Tipo di prodotto | Trovatori Stud |